TRAILBLAZER^™ Heavy-Duty V-PLOW & STRAIGHT BLADE SNOWPLOWS

We design and manufacture our own hydraulics to ensure the highest standards of performance, quality, and durability—giving you a plow that is fast, responsive, and built to last. This allows plow drivers to change the blade position quickly and easily for efficient plowing.

All critical hydraulic components are fully enclosed for protection from the elements.

Receiver brackets can be easily removed, restoring your vehicle back to its original ground clearance when the plow is not in use.

The FISHER^® Scrape Lock system locks the plow in any position you put it in to give you a cleaner scrape, especially while back dragging. With the plow locked in place, Scrape Lock gives you the performance of a larger plow without the extra weight and without the need to push any extra buttons.

Hooking up the TRAILBLAZER™ v-plow or straight blade is simple. With the receiver brackets installed on your utility vehicle, either drive in or manually push the plow into the receivers. Push up on the headgear to engage the hitch pins in the receiver holes, then slide the handle to lock the hitch pins in place. Finally, connect the electrical plug.

Detaching the plow is just as easy. The receivers are removable, to maintain ground clearance.

Designed for easy installation onto a wide range of tractor models, these mount kits make it possible for the TRAILBLAZER heavy-duty straight blade and v-plow to fit on a compact tractor. They are flared both vertically and horizontally to ensure proper alignment and make the drive-in connection easier. The push beam, which makes up the front portion of the mount, can be quickly detached to allow for a loader attachment.

The 6′ wide, 14-gauge powder coated steel moldboard and standard 5″ high-carbon steel cutting edge make the TRAILBLAZER™ straight blade a strong choice that is the right size for your UTV.

With four vertical ribs and high-strength, low-weight, alloy steel construction, the TRAILBLAZER™ UTV straight blade is strong enough for commercial operation and light enough to fit most UTVs.

Two heavy-duty coil springs protect your plow and UTV by allowing the whole blade to trip when striking obstacles.

Featuring a 6′ wide powder coated steel flared moldboard, the TRAILBLAZER™ UTV v-plow blades go from a 25 ¾” center height to a full 29 ¼” at the outer edge.

A high-carbon steel cutting edge also comes standard, increasing wear resistance.

The high-strength, low-weight alloy steel components are both stronger and lighter than traditional steel, so your utility vehicle can work hard without having to carry the extra weight on your UTV frame like with heavier plows. The TRAILBLAZER™ v-plow blade is reinforced with six vertical ribs, and features the strength of our proven T-frame design.

Each v-plow blade features independent trip-edge protection to get over bumps and hidden obstacles, whether in V, scoop or straight blade configuration, helping to protect the plow, the UTV and the operator. Since only the bottom edge trips, snow stays in front of the blade, so you can keep on going without dumping the entire load of snow.

The FISHER^® trip edge uses compression-type springs that never require adjustment and will not wear out like extension springs.

Double-acting cylinders allow the operator to lock the wings together to use the v-plow in straight blade mode with single button control. Double-acting cylinders also hold the wings firmly in place for clean, efficient back dragging.

For exceptional snow containment in all positions, the TRAILBLAZER™ UTV v-plow has a center deflector designed to prevent snow from going over the top of the blade and the formed cutting edges reduce trailing snow.

When fully angled or in V mode, the TRAILBLAZER™ UTV v-plow plowing path is 5′ wide, and 4′ 7″ in scoop. For UTVs with a wider wheel base, a width-adjustment setting is available to make your plowing path wider in these positions. Using the alternate setting, the plowing width is 5′ 6″ when fully angled or in V, and 5′ 1″ in scoop.