STEEL-CASTER™ (1.5 – 6.0 cu yd) ACCESSORIES
Filter By
Filter By

PRE-WET SYSTEM
The pre-wet system accessory allows the operator to activate deicing material by applying a liquid deicing agent directly on the material prior to leaving the hopper, providing you with increased material efficiency and superior ice control.
Part Numbers
#76400 | ON/OFF Pump Kit |
#76420 | Full Feature Pump Kit, FISHER® |
#76425 | Pre-Wet 50 Gal Tank Kit* (Two 25 gal tanks) |
#76450 | Pre-Wet 100 Gal Tank Kit* (Two 50 gal tanks) |
*Additional tank kits are not compatible with a vibrator |

POLY LID KIT
Shields de-icing material from the elements, locks out moisture to prevent material bridging and protects against material overflow while loading.
Part Numbers
#72750 | Regular Capacity (1.5, 2 & 3 cu yd) |
#72770 | High Capacity (Both 4.5 & 6.0 cu yd) |

SPILL GUARD KIT
Available in 50" and 70" widths to cover the full range of STEEL-CASTER™ hopper spreaders, the Spill Guard Kit provides the loader with an improved line of sight to the hopper edges, while preventing material from overflowing into the bed of the truck from off-center loading.
Part Numbers
#81119 | 70" Kit |
#81120 | 50" Kit |

LICENSE PLATE KIT
Stay legal with our quality illuminated License Plate Kit. This genuine FISHER® license plate kit has been specifically designed for your hopper and allows you to move your license plate to a spot that is visible and legally compliant.
Part Numbers
#99686 | For All Models |

STROBE LIGHT KIT
Make sure you're seen, day or night, with our complete hopper Strobe Light system. Constructed from high impact plastic, and rated beyond -20º F, this yellow LED strobe system has been designed to last and will ensure that you're seen in even the worst of conditions.
Part Numbers
#99494 | For All Models |

VIBRATOR KIT
Designed to help move stubborn material and prevent bridging, a genuine FISHER® Vibrator system will ensure that less-than-ideal material, which is prone to bridging and clogging, will not hold you up when you need to be on the move.
Part Numbers
#76668 | For All Models* |
*Only compatible with one 50 gal pre-wet tank kit or one 100 gal pre-wet tank kit |

WORK LIGHT KIT
A genuine FISHER® Work Light system will grant you increased visibility at the rear of your spreader. Encased in anodized aluminum, and rated beyond -20º F, this LED Work Light system projects over 1000 lumens to help you monitor material distribution and illuminate potential hazards while backing up.
Part Numbers
#99505-1 | For All Models |

SECONDARY WORK LIGHT KIT
Take it up a notch with a genuine FISHER® secondary work light kit. Designed to integrate with our work light kit (99505-1), this accessory kit will provide an addition 1000 lumens of light on the opposite side of your FISHER spreader.
Part Numbers
#99732-1 | For All Models |

6" SIDE EXTENSIONS
Increase the capacity of your STEEL-CASTER™ hopper spreader with this 6" Side Extensions Kit. The increase in capacity will vary depending on the size of your spreader; increased material capacity will vary from .5 to 1 yard. Each kit contains the corner brackets, hardware and installation instructions, but does not provide the side board material.
Part Numbers
#99488 | For All Models |

CENTRAL POINT GREASE KIT
The Central Point Grease Kit provides easy access to grease points, simplifying preventative maintenance greasing that is essential to maximize bearing life.
Part Numbers
#11763 | For All Models |

TIE-DOWN CHAIN KIT
A Tie-Down Chain Kit provides additional in-bed stability and security. 72 inches of high-strength steel chain and binder allow you to add an extra measure of safety as you move tons of material down the road. Each kit contains four chain binder assemblies. (Hoppers require bolting to the truck frame for proper operator safety.)
Part Numbers
#99690 | For All Models |

MASTER ACCESSORY HARNESS
Integrate all your accessories with this convenient kit. Includes all the wiring needed to go from cab to spreader, an in-cab control panel, and rear of hopper storage for accessory fuses and relays, allowing total integration of our plug and play accessories. Hydraulic model master accessory harness kit shown.
Part Numbers
#99629 | For All Gas Models |
#99627 | For All Hydraulic Models |

VEHICLE-SIDE HARNESS KIT
The Vehicle-Side Harness Kit contains components to replace harnessing on the truck or wire a second truck to operate the spreader.
Part Numbers
#78402 | For All Models |

SPREADER CONTROL ADAPTER PLATE FOR CUP HOLDER MOUNT
Gain the flexibility and easy installation benefits of the cup holder control mount with every spreader installation using the new Spreader Control Adapter Plate Kit. Kit contains a durable metal mounting plate and hardware. Cup Holder Mount not included, order separately (#82006).
Part Numbers
#82018 | For All Models |

CONTROL CUP HOLDER MOUNT
The Control Cup Holder Mount is designed to fit firmly in most vehicle cup holders. It's a genuine, factory-tough accessory specifically engineered to securely hold FISHER® hand-held or joystick controls and all types of smart phone devices (not included with mount). This flexible gooseneck mount has a 360-degree rotation and ensures optimal, customizable positioning.
Part Numbers
#82006 | For All Models |

DIELECTRIC GREASE
Keep your FISHER® plow running strong. Apply our specially formulated dielectric grease after each use to prevent corrosion caused by electrolysis and highly corrosive de-icing agents.
Part Numbers
#22400K | 2 oz. Tube |

FREEZE GUARD™ GREASE
Specially formulated to protect moving components in arctic mining conditions, this grease is ideal for bearings, hinges and pivot bolts on snow and ice control equipment. The custom formula maintains viscosity from -40 up to 300 degrees, and military-grade, corrosion-prevention additives protect equipment from corrosion without harmful environmental impact. FREEZE GUARD™ Grease is available in cartridges, pails, totes and drums.
Part Numbers
#72901 | 14oz Cartridges |
#72902 | 7 lb Pail |
#72903 | 120 lb Tote |
#72904 | 400 lb Drum |